Skip to content

Garage door spring replacement cost (2026): torsion vs extension, one or both

2026 garage door spring replacement cost: $150–$400 torsion, $75–$250 extension. Why you should replace in pairs, cycle life, and why this is almost always a pro job.

Cost: $150–$400 typicalTime: 45–90 minDifficulty: Pro only (torsion) / experienced DIY (extension)
By Ken Hoven · Published

A broken garage door spring sounds like a gunshot. The door won't open, the opener grinds if you try, and the quote the first repair company gives you often has a zero in it that shouldn't be there. (Twice-a-year spring and cable checks are on the seasonal maintenance checklist for a reason.) Here's what spring replacement actually costs in 2026, why you almost always replace in pairs, and why the torsion spring is one of the few home repairs most pros will tell you not to DIY.

Quick cost summary

Scenario Typical 2026 installed cost
One torsion spring, standard size $150–$280
Pair of torsion springs (recommended) $250–$450
One extension spring (lighter doors) $75–$180
Pair of extension springs $150–$280
High-cycle (20,000+ cycle) spring upgrade +$80–$200 per spring
After-hours / emergency surcharge +$75–$200
Common "upsell" quote range (shop around) $500–$1,200

If a quote is over $500 for a standard same-day residential torsion spring pair, get a second opinion. This is one of the most upsold repairs in the industry — some chains quote $700–$1,500 for a job that honest independents do for $250–$450.

Torsion vs extension — know which you have

Torsion springs are mounted on a horizontal bar above the door opening, parallel to the top of the door. Standard on modern garage doors (post-1990s), on heavier doors, and on 2-car-wide doors. Store energy by winding. Most residential doors have one or two torsion springs.

Extension springs run along the horizontal tracks on either side of the door, parallel to the ceiling. Stretch when the door closes, contract to help lift it. Older and lighter doors; still common on single-car doors in starter homes. Always come in pairs (one per side).

Look above the door right now:

  • Rod + springs across the top = torsion
  • Long stretched springs beside the tracks = extension

Why you replace springs in pairs

Springs installed at the same time are identical in cycle wear. When one goes, the other has used the same number of cycles and is also near the end of its life — often within days to weeks.

A good pro will quote you both. A less honest one will replace one, charge you the full service call, then come back in three months and charge you another full service call when the second one breaks. Pay the extra $100 and do the pair.

Exception: springs installed at different times (one was replaced 2 years ago, the other is the original from 20 years ago) — just replace the original.

Cycle life — the honest number

A garage door spring is rated in cycles (one open + one close = one cycle):

Spring grade Rated cycles Typical life
Standard builder-grade 10,000 5–7 years in average use
Standard replacement 15,000 7–10 years
High-cycle 20,000 10–15 years
Ultra high-cycle 25,000–100,000 15+ years

Average household uses the garage door 4–6 cycles per day. Pay the extra $80–$200 per spring for a 20,000-cycle version if you use the garage as your main entry — it pays for itself the first time you avoid a service call.

Why this is pro work (torsion especially)

A loaded torsion spring stores enormous rotational energy — the equivalent of about 200 lb of torque in a fully-wound residential spring. Unwinding it safely requires:

  • Two winding bars (not screwdrivers; steel 18" bars)
  • Correct spring size (wire gauge, inside diameter, length) — matching the door weight
  • Knowing which direction to unwind (left-wound vs right-wound; they're not interchangeable)
  • Proper torque recovery on the new spring
  • Setting the correct number of turns (typically 7–7.75 for standard 7-ft doors, more for 8-ft)

The failure mode is severe. A spring that lets loose while being unwound has killed and injured enough homeowners that major manufacturers include explicit "do not service without a professional" warnings. Pros charge $150–$280 for the first spring and $80–$150 for the second because the service call is the fixed cost — you're mostly paying for someone who knows how to not get hurt doing it.

Extension springs are less dangerous because they're stretched linearly rather than wound. An experienced DIYer with a safety cable through the spring can replace one safely. Still not recommended as a first-time garage door DIY.

What a legitimate quote should include

  • Spring(s) of the correct size and cycle rating
  • Service call / labor (typically 45–90 minutes on site)
  • Door balance test after install (door should hold its position at waist height with no opener assist)
  • Safety cables for extension springs (not optional; prevents the spring from flying if it snaps)
  • Center bearing replacement for torsion if the old one is rough ($15–$40 part) — often needed and usually bundled

Common upsell tactics to decline

The repair industry has some bad actors. Watch for:

  • "Both springs are high-cycle, that'll be $800." High-cycle costs $80–$200 extra per spring over standard. $800 for a pair of high-cycle torsion springs is roughly $300–$500 over fair price.
  • "Your cables are also worn, that'll be another $200." Cables ($5–$20 part) should be replaced only if visibly frayed or kinked. Ask to see them.
  • "Your drum and bearings are shot." Rare on a door under 15 years old. Ask for inspection.
  • "You need a whole new door." Only true if the door panels are physically damaged. Springs and door are separate systems.

Price-check protection: when you call, get a clear quote on the phone for "replacement of one standard torsion spring, standard 7-ft door, standard size." If their on-site quote exceeds that by more than 20%, don't authorize the work. Pay the service call fee if any, send them away, and call someone else.

DIY the extension spring?

If you have extension springs, a safety cable, two matched springs, and have watched a tutorial video twice, you can do it. The door must be fully open (fully closed = loaded) before you touch the springs. Full procedure is beyond this cost guide — manufacturer instructions or the DDM Garage Doors YouTube channel are safer references than any written guide.

Save a day's wages? Maybe. Risk injury from a spring letting go? Also yes. Honest call: if the labor cost quote is $150, it's not worth the risk.

Parts and tools on Amazon (for extension-spring DIYers)

  • Extension spring pairs with safety cables — match the color code to your old springs (color = strength rating).
  • Safety cables for extension springs — essential, run through the inside of each spring.
  • Torsion spring winding bars (steel, 18") — for torsion springs. Still recommend a pro, but if you're going.
  • Garage door lubricant (silicone, not WD-40) — monthly application extends spring life.
  • Nylon garage door rollers — quiet upgrade from steel. $30–$60 for a set of 10.
  • Digital torque wrench — if you're setting torsion turns precisely.

As an Amazon Associate, Home Repair Planner earns from qualifying purchases.

Related upgrades worth bundling

  • New opener — if your opener is 15+ years old, bundling spring service with opener replacement often saves one service call. New smart openers are $200–$400 plus $150–$300 install.
  • Lubrication service — a pro can lube all hinges, rollers, bearings, and the torsion shaft in 10 minutes. Ask for it bundled; often free with spring service.
  • Weather seal replacement — the rubber at the bottom. $25–$75 part, 15-minute job.

Common questions

How much does it cost to replace a garage door spring?

In 2026, a single torsion spring runs $150–$280 installed, a pair runs $250–$450. Extension springs are cheaper: $75–$180 single, $150–$280 pair. After-hours service adds $75–$200.

Should I replace one or both garage door springs?

Both, if they were installed at the same time. They've used the same number of cycles, and the second will break within weeks to months of the first. The extra spring on the same service call is $80–$150; a second service call later is $150–$280.

Can I replace a garage door spring myself?

Extension springs can be DIY'd with safety cables and proper technique. Torsion springs should not be DIY'd — the stored energy is enough to cause serious injury, and the pro job is $250–$450, which is cheap for the risk.

How long do garage door springs last?

Standard 10,000-cycle springs last 5–7 years in average use (4–6 cycles/day). 15,000-cycle springs last 7–10 years. 20,000+ cycle springs last 10–15 years. Use correlates with life — rental properties and families using the garage as the main entry wear springs out faster.

Why is my garage door spring quote so high?

Some national chains and emergency services quote $500–$1,500 for a pair of standard torsion springs. Fair market rate for standard residential is $250–$450. Shop around — get 2–3 phone quotes before accepting any on-site quote over $500.

Is a broken spring an emergency?

Only if your car is trapped inside. The door is typically not operable (opener will refuse or burn out trying), but the house is safe. Calling in the morning for same-day service costs $75–$200 less than after-hours.

About these numbers: cost ranges are typical 2026 U.S. planning figures compiled from published cost guides and retailer pricing. They are not quotes. Verify prices locally, and use a licensed professional for electrical, gas, roofing, structural, and permit-required work.

Some links on this page are affiliate links. As an Amazon Associate, Home Repair Planner earns from qualifying purchases. Contractor quote requests go through Networx, which is paid by participating contractors; we may earn a referral fee. Full disclosure.