Skip to content

Home repair costs in Dallas–Fort Worth, TX (2026)

Dallas–Fort Worth is in the typical (national) tier for home repair pricing — most suburbs and mid-size metros. Rapid growth drives strong contractor demand. The 2021 winter storm exposed how many homes lacked freeze-proof plumbing — water heater and plumbing upgrades surged afterward.

AC replacement cost in Dallas–Fort Worth: $6,900 – $9,300

A typical AC replacement in Dallas–Fort Worth runs $6,900 to $9,300 installed in 2026, with a midpoint near $8,000. That is in line with the national planning estimate of $6,900–$9,300. This is licensed trade and permit work, not a DIY job.

Priced for: 3-ton system, mid-tier 16–17 SEER2, existing ductwork reused, AC only.

Where a typical Dallas–Fort Worth price goes
Condenser + matched indoor coil, 3-ton, 16–17 SEER2 two-stage$4,100 – $5,600
Crew labor, one day (typically two technicians), startup and commissioning$1,700 – $2,400
Line set flush or replacement, pad, disconnect, whip, thermostat$600 – $700
Permit, refrigerant charge, recovery and disposal of old equipment$500 – $600

AC replacement cost by system size in Dallas–Fort Worth

1.5 ton (up to ~900 sq ft)$4,200 – $5,500
2 ton (~1,000–1,300 sq ft)$4,600 – $6,200
2.5 ton (~1,300–1,600 sq ft)$5,750 – $7,750
3 ton (~1,600–2,000 sq ft)$6,900 – $9,300
3.5 ton (~2,000–2,300 sq ft)$8,050 – $10,850
4 ton (~2,300–2,700 sq ft)$9,200 – $12,400
5 ton (~2,700–3,300 sq ft)$11,500 – $15,500

Installed, with everything else held at: Efficiency tier: Mid — 16–17 SEER2; Ductwork: Good — reuse as is; Replace the furnace / air handler too?: No — AC only (condenser + coil).

What moves this price in Dallas–Fort Worth

  • •Texas licenses air conditioning contractors through the Department of Licensing and Regulation, and doing AC work for a fee without that license is a violation. Look up the contractor's license number before you sign. Source: Texas Department of Licensing and Regulation — AC contractor penalties and sanctions
  • •Permit: typically $50–$200 for residential work. Permit requirements vary across DFW's many municipalities. Dallas, Fort Worth, Arlington, and Plano each have their own building departments and fee schedules.
Get AC replacement quotes in Dallas–Fort Worth →

Quote requests are handled by Networx. No charge to you; Home Repair Planner may earn a fee. Disclosure

Price your own job in the AC replacement calculator · Dallas–Fort Worth permits, signs to replace and sources

Roof replacement cost in Dallas–Fort Worth: $10,550 – $16,800

A typical roof replacement in Dallas–Fort Worth runs $10,550 to $16,800 installed in 2026, with a midpoint near $13,500. That is in line with the national planning estimate of $10,550–$16,800. This is licensed trade and permit work, not a DIY job.

Priced for: 1,600 sq ft footprint, medium pitch (about 19 squares), architectural asphalt, one story, one existing layer.

Where a typical Dallas–Fort Worth price goes
Architectural shingles, underlayment, ice-and-water shield, drip edge, flashing, vents$3,500 – $5,600
Labor: tear-off and installation, crew of 3–6, 1–3 days$5,100 – $7,800
Dumpster and disposal of one existing layerPermit fees and rotted-decking replacement are not included; the calculator notes them as extras$1,900 – $3,400

Roof replacement cost by house size in Dallas–Fort Worth

1,000 sq ft footprint$6,600 – $10,500
1,500 sq ft footprint$9,900 – $15,750
2,000 sq ft footprint$13,200 – $21,000
2,500 sq ft footprint$16,500 – $26,250
3,000 sq ft footprint$19,800 – $31,500

Installed, with everything else held at: Roof pitch: Medium (4/12–7/12) — typical; Material: Architectural asphalt shingle; Stories: 1 story; Existing layers to tear off: 1 layer.

Roof replacement cost by material in Dallas–Fort Worth

3-tab asphalt shingle$9,600 – $13,900
Architectural asphalt shingle$10,550 – $16,800
Standing-seam metal$19,200 – $34,100
Concrete or clay tile$21,100 – $37,900

Installed, with everything else held at: House footprint: 1,600 sq ft; Roof pitch: Medium (4/12–7/12) — typical; Stories: 1 story; Existing layers to tear off: 1 layer.

What moves this price in Dallas–Fort Worth

  • •Hail and wind damage from severe storms
Get roof replacement quotes in Dallas–Fort Worth →

Quote requests are handled by Networx. No charge to you; Home Repair Planner may earn a fee. Disclosure

Price your own job in the roof replacement calculator · Dallas–Fort Worth permits, signs to replace and sources

Water heater replacement cost in Dallas–Fort Worth: $1,200 – $2,450

A typical water heater replacement in Dallas–Fort Worth runs $1,200 to $2,450 installed in 2026, with a midpoint near $1,800. That is in line with the national planning estimate of $1,200–$2,450. Doing it yourself, materials run about $800–$1,550.

Priced for: 50-gallon gas tank, like-for-like swap, easy access (garage or basement).

Where a typical Dallas–Fort Worth price goes
50-gallon gas tank water heater, mid-grade$700 – $1,300
Plumber labor, 2–4 hours, including flex connectors and fittings$400 – $900
Permit, inspection, and haul-away of the old unitCode-required extras (expansion tank, pan, strapping) are priced by the calculator when you select them$75 – $250

Water heater replacement cost by type and size in Dallas–Fort Worth

Gas tank, 40 gal$1,100 – $2,250
Gas tank, 50 gal$1,200 – $2,450
Electric tank, 40 gal$950 – $2,050
Electric tank, 50 gal$1,050 – $2,150
Tankless gas (whole-house)$2,000 – $4,250
Heat pump (hybrid), 50 gal$2,250 – $3,850
Heat pump (hybrid), 65 gal$2,550 – $4,250
Heat pump (hybrid), 80 gal$2,850 – $4,750

Installed, with everything else held at: Same type as the old one?: Yes — like-for-like swap; Location: Garage or basement, easy access.

What moves this price in Dallas–Fort Worth

  • •Permit: typically $50–$200 for residential work. Permit requirements vary across DFW's many municipalities. Dallas, Fort Worth, Arlington, and Plano each have their own building departments and fee schedules.
Get water heater replacement quotes in Dallas–Fort Worth →

Quote requests are handled by Networx. No charge to you; Home Repair Planner may earn a fee. Disclosure

Price your own job in the water heater replacement calculator · Dallas–Fort Worth permits, signs to replace and sources

Interior painting cost in Dallas–Fort Worth: $400 – $850

A typical interior painting in Dallas–Fort Worth runs $400 to $850 installed in 2026, with a midpoint near $625. That is in line with the national planning estimate of $400–$850. Doing it yourself, materials run about $220–$280.

Priced for: One 12×12 room with 8-ft ceilings, walls only (about 380 sq ft of wall), mid-grade paint, walls in good condition.

Where a typical Dallas–Fort Worth price goes
Paint and sundries: about 3 gallons mid-grade, rollers, tape, drop cloths$110 – $160
Painter labor: prep, cut-in, two coats on about 380 sq ft of wall$285 – $650
Minor patching and caulkCeilings, trim, extra rooms, and heavy repair are priced by the calculator$25 – $45

Interior painting cost by number of rooms in Dallas–Fort Worth

1 room$400 – $850
2 rooms$850 – $1,700
3 rooms$1,250 – $2,550
5 rooms$2,100 – $4,300
8 rooms$3,350 – $6,850

Installed, with everything else held at: Paint ceilings too?: No — walls only; Trim, doors & baseboards: Leave as is; Paint quality: Mid-grade ($50/gal) — recommended; Wall condition: Good — minor nail holes.

Cost to paint one 12×12 room, walls only vs. walls and ceiling in Dallas–Fort Worth

No — walls only$400 – $850
Yes — walls and ceilings$550 – $1,150

Installed, with everything else held at: Rooms to paint: 1 rooms; Trim, doors & baseboards: Leave as is; Paint quality: Mid-grade ($50/gal) — recommended; Wall condition: Good — minor nail holes.

Get interior painting quotes in Dallas–Fort Worth →

Quote requests are handled by Networx. No charge to you; Home Repair Planner may earn a fee. Disclosure

Price your own job in the interior painting calculator · Dallas–Fort Worth permits, signs to replace and sources

Deck staining cost in Dallas–Fort Worth: $900 – $1,950

A typical deck staining in Dallas–Fort Worth runs $900 to $1,950 installed in 2026, with a midpoint near $1,400. That is in line with the national planning estimate of $900–$1,950. Doing it yourself, materials run about $290–$380.

Priced for: 300 sq ft deck plus 40 linear ft of railing, clean-and-brighten prep, semi-transparent stain.

Where a typical Dallas–Fort Worth price goes
Stain, cleaner, and brightener for about 300 sq ft (roughly 4 gallons of stain)$150 – $250
Labor on the deck floor: wash, brighten, dry time, light sanding, apply$550 – $1,250
Railings and balusters, about 40 linear ftStripping an old failed finish is a separate line in the calculator$200 – $450

Deck staining cost by deck size in Dallas–Fort Worth

150 sq ft$600 – $1,300
300 sq ft$900 – $1,950
500 sq ft$1,300 – $2,850
800 sq ft$1,900 – $4,200

Installed, with everything else held at: Railing length: 40 linear ft; Current condition: Clean & brighten only (sound finish or bare wood); Stain type: Semi-transparent (1–2 coats).

Get deck staining quotes in Dallas–Fort Worth →

Quote requests are handled by Networx. No charge to you; Home Repair Planner may earn a fee. Disclosure

Price your own job in the deck staining calculator · Dallas–Fort Worth permits, signs to replace and sources

Estimate, not survey data. These Dallas–Fort Worth figures are the national planning estimate adjusted by the typical (national) regional multiplier (1×). They are not contractor quotes; actual bids will vary with system size, materials, access and condition. How the estimates are built

About the Dallas–Fort Worth market

Climate

Humid subtropical — summers around 96°F, winters around 34°F. Long cooling season (April–October) combined with occasional hard freezes that stress plumbing and water heaters.

Best scheduling window

March through May and October through November for exterior work. Summer is too hot for comfortable roofing and painting. AC replacement is best scheduled in spring before peak demand.

Typical permit costs

$50–$200 for residential work. Permit requirements vary across DFW's many municipalities. Dallas, Fort Worth, Arlington, and Plano each have their own building departments and fee schedules.

Metro population

7.6 million (MSA)

What drives costs in Dallas–Fort Worth

  • •Hail and wind damage from severe storms
  • •Large homes (median ~2,200 sq ft) mean bigger systems
  • •Multiple jurisdictions with different permit requirements
  • •Expansive clay soils cause foundation movement that affects all systems

Compare with other cities

Last updated November 2026. All figures are planning estimates, not quotes. Methodology