Furnace replacement cost in Denver, CO (2026)
| Condensing gas furnace, 60–80k BTU, single-stage | $2,185 – $3,450 |
| Labor, one day for 1–2 technicians, including startup | $1,380 – $2,185 |
| PVC intake/exhaust run, condensate drain or pump, gas and electrical reconnection, thermostat | $690 – $1,265 |
| Permit, inspection, haul-away | $345 – $575 |
Estimate, not survey data. These Denver figures are the national planning estimate adjusted by the higher-cost metro regional multiplier (1.15×). Actual quotes will vary. Try the interactive calculator →
Denver homeowners can expect to pay $4,600 to $7,475 for a typical furnace replacement project in 2026, 15% above the national average. Highest average homeowner spending on improvements in the U.S. ($14,200/year). Altitude requires gas appliance derating, and intense UV at elevation accelerates exterior paint and roof degradation.
Pricing the other half of the system? AC replacement cost in Denver has its own estimate.
Why furnace replacement costs differ in Denver
Denver falls into the higher-cost metro tier for home repair costs — large metros: chicago, denver, atlanta, phoenix, minneapolis, portland. Several local factors drive this:
- •Altitude derating for gas appliances adds complexity
- •Intense UV degrades exterior finishes faster
- •Hail damage is common (affects roofing and painting quotes)
- •Strong construction market keeps labor costs elevated
Denver climate and scheduling
High altitude (5,280 ft) affects gas appliance sizing and combustion — furnaces and water heaters must be derated for altitude.
May through September for exterior work. Hailstorms peak in June and July — schedule roofing before or after. Furnace replacement is best in September before the heating season.
Furnace replacement permits in Denver
Residential permit fees in Denver, CO typically run $50–$200 for this type of work. Denver CPD handles permits through the eDPS portal. Standard residential water heater and furnace permits process in about 5 business days. High altitude affects gas appliance sizing.
Your contractor should pull the permit and build the fee into their quote. If they suggest skipping the permit, that's a red flag — unpermitted work can create problems with insurance claims, home sales, and code compliance.
Signs it's time to replace in Denver
High altitude (5,280 ft) affects gas appliance sizing and combustion — furnaces and water heaters must be derated for altitude. Watch for these signs:
- ⚠The furnace is 15–20+ years old and needs a repair costing more than about a third of a new unit
- ⚠A cracked heat exchanger — a safety condition, and effectively the end of the furnace
- ⚠Frequent breakdowns, short cycling, or a blower or control board failure on an old unit
- ⚠Yellow or flickering burner flames, soot, or a CO alarm event (shut it down and call a pro)
- ⚠Rising gas bills and uneven heat despite a clean filter and sealed ducts
Get a more specific estimate
The figures above are for a typical job in Denver. Your project may differ based on system size, materials, access, and condition. Use our interactive calculator to adjust the inputs for your specific situation.
Open the furnace replacement calculator →Other home repair costs in Denver
Furnace replacement cost in other cities
Where these numbers come from
National figures come from the sources below. Denver figures apply the higher-cost metro regional multiplier (1.15×) to account for local labor rates and cost of living.
| Source | Published figure | Basis |
|---|---|---|
| Carrier — Gas Furnace Replacement Guide | Installed cost of a new furnace typically $3,800–$12,000 in 2026 | Manufacturer guidance |
| HVACBase — Furnace Installation Cost (2026) | Gas furnace $3,500–$8,500 installed, national average $5,500 | Editorial estimate |
| Inch Calculator — Cost to Install a Furnace | $5,000–$7,500 for a 2,000 sq ft home reusing existing ductwork, average about $6,250 | Editorial estimate |
Last updated November 2026. Figures are planning estimates, not quotes. Methodology · Disclosure